HIOS electric screwdrivers

We are a representative of HIOS high end power tools from Japan. The product range consists of electric screwdrivers, torque meters, tappers and screws.

IPA International is the representative in the Netherlands of HIOS electric screwdrivers

HIOS aims to provide the highest quality and tot create a comfortable working environment from the viewpoint of customers.

The HIOS new fastening system is a comprehensive system that achieves highly reliable screw tightening and high quality control.

HIOS general information
HIOS message from the president

HIOS range electric screwdrivers

— Torque range: 0,03 – 4,5 N.m —

Hios DC screwdrivers (low voltage systems)

Brushless electric screwdrivers

BLG-BC1 series (DC Type)

No more overlooked tightening errors!
  • It prevents human errors in operations! It supports accurate screw fastening and reduces the operator’s fatique.
  • A convential external screw counter is not required. This realizes low-cost introduction of new screwdrivers.
  • The integration of the screwdriver and the counter is optimal for space-saving
    operations.
Lever start type

BLG-4000BC1: Output Torque range N.m 0.1-0.55

Two-way Start Sytem

BLG-5000BC1: Output Torque range N.m 0.2-1.2
BLG-5000BC1-15: Hi-speed rotation Output Torque range N.m 0.2-1.2
BLG-5000BC1-18: Hi-speed rotation Output Torque range N.m 0.5-1.5
BLG-5000BC1-HT: Hi-Torque Output Torque range 0.5-2.0

 

Accessories
  • Suction (Vacuum) Attachment for BLG Series
    By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.
    BLG-4000BC1, BLG-5000BC1, BLG-5000BC1-15
  • Vertical Screwdriver Operating Stand VMS-40/ VMS-50.
BLG-BC2 series (DC Type)

No more rely operations experience and skill!
  • Detect errors in screw fastening in real time with high accurancy by counting the pulse of the motor.
  • Misplaced screws of different type or lenght, recessed screw or floating screws due to seized cables are now detected.
  • Installed serial port (RS-232C) makes it possible to set the driver by remote control and record pulse values of each screw tightening for traceability.
  • Direct teaching allows a simple setting.
Lever start type

BLG-4000BC2: Output Torque range N.m 0.1-0.55

Two-way Start System

BLG-5000BC2: Output Torque range N.m 02.-1.2
BLG-5000BC2: 15 Hi-speed rotation Output Torque range N.m 0.3-1.0
BLG-5000BC2: 18 Hi-speed rotation Output Torque range N.m 0.5-1.5
BLG-5000BC2-HT: Hi-Torque Output Torque range N.m 0.5-2.0

Accessories
  • Suction (Vacuum) Attachment for BLG Series
    By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.
    BLG-4000BC2, BLG-5000BC2, BLG5000BC2-15
  • External Input/ output cable BLG-BC2-3010
  • Vertical Screwdriver Operating Stand VMS-40/ VMS-50
Related Products
  • Eternal I/O Box BLG-IO-Pro1
BLG-ZERO1 series (DC Type)

Anyone can be a skilled craftsman in 30 seconds!
  • Direct teaching makes it easy to configure settings.
  • The pulse of the motor is counted, enabling real time detection of screws fastening errors with a high degree of accuracy.
  • Errors such as mixing of wrong types of screws, unseated screws, cam out, striped screw holes or parts caught in screws can be detected.
  • It displays the remaining number of screws to fasten every time a screw is fastened.
Lever Start type

BLG-4000ZERO1: Output Torque range N.m 0.1-0.55

Two-way Start System

BLG-5000ZERO1: Output Torque range N.m 0.2-1.2
BLG-5000ZERO1-15: Hi-speed rotation Output Torque range N.m 0.3-1.0
BLG-5000ZERO1-18: Hi-speed rotation Output Torque range N.m 0.5-1.5
BLG-5000ZERO1-HT: Hi-Torque Output Torque range N.m 0.5-2.0

Accessories
  • Suction (Vacuum) Attachment for BLG Series
    By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.
    BLG-4000ZERI1, BLG-5000ZERO1, BLG-5000ZER01-15
  • Vertical Screwdriver Operating Stand VMS-40/ VMS-50.
BLG series (DC Type)

The New Industry Benchmark in Electric Torque drivers!
  • The BLG series has the performance, quality and durability equivalent to excisting brushless screwdrivers (e.g. BL series), plus better maintenance efficiency.
  • You can smoothly switch from a brushed screwdriver (e.g. CL series) to a brushless screwdriver (e.g. BLG series) without significant cost increase.
Lever Start Type

BLG-4000: Output Torque range N.m 0.1-0.55

Two-way (Push/ Lever) Start Type
BLG-5000: Output Torque range N.m 0.2-1.2
BLG-5000-15: Hi-speed rotation  Output Torque range N.m 0.3-1.0
BLG-5000-18: Hi-speed rotation Output Torque range N.m 0.5-1.5
BLG-5000-HT: Hi-Torque Output Torque range N.m 0.5-2.0

 

Accessories
  • Suction (Vacuum) Attachment for BLG Series
    By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.
  • Vertical Screwdriver Operating Stand VMS-40/ VMS-50.
Related Products
  • I/O Signal Relay Box BLOP-AF
    A complete signal from the screwdriver can be easily extracted and used by connecting this Relay box to an external device such as PLC.
  • BLG-OPC Series I/O Signal Relay Box for Automation BLOP-OST2.
    By connecting this box to a set of the BL-OPC or BLG-OPC and its power supply, the driver can start/stop by inputting D-ACT signals into the CN3 connector with external devices.
BL series (DC Type)

The first Brushless Electric Torque driver in the world!
  • There is no carbon powder emission and maintains a clean environment.
  • Significant durability improvement considerably reduces maintaince cost.
  • Reduces the temperature rise of the motor by about 30% and mitigates problems related to heating.
  • Two types of start systems (push and lever) are available with one screwdriver (except BL-2000)
  • High-speed rotation shortens screw fastening time and improves work efficiency.
Lever Start type

BL-2000: Output Torque range N.m 0.02-0.2
Two-way (Push/Lever) Start type
BL-3000: Output Torque range N.m 0.2-0.55
BL-3000SS: Impact absorbing Output Torque range N.m 0.2-0.35
BL-5000:Output Torque range Nm 0.2-1.2
BL-5000SS: Impact absorbing Output Torque range N.m 0.2-1.2
BL-5000-15: Hi-speed rotation Output Torque range N.m 0.3-1.2
BL-5020: Hi-Torque Output Torque range N.m 0.5-2.0
BL-7000: Hi-Torque Output Torque range N.m 0.7-2.8
BL-7000HT: Hi-Torque Output Torque range N.m 0.7-3.5

 

Accessories and Applicable Drivers
  •  Suction (Vacuum) Attachment for BL Series
    By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.
    BL-2000, BL-5300, BL-5000, BL-7000
  •  Anti-electrostatic BL-ESD. The screwdriver body is made from an anti-electrostatic material to prevent the generation of static electricity which is suitable for the assembly of precison equipment and electronic parts.
    BL-3000ESD, BL-5000ESD, BL-5000ESD-15, BL5020ESD, BL-7000ESD, BL-7000HT-ESD
  • Suction + Anti-electrostatic BLQ-ESD BLQ-3000ESD, BLQ-5000ESD, BLQ-5000ESD-15, BLQ-7000ESD
  • Clean Room BLQ-CR
    BLQ-2000CR, BLQ-3000CR, BLQ-5000CR, BLQ-500CR-15
  • Clean Room + Anti-electrostatic BLQ-CR-ESD
    In addition to anti-electrostatic, two vacuum units are installed in both the body and the Suction Attachment to remove powder dust generated in screw fastening.
    BLQ-2000CR, BLQ-3000CR-ESD, BLQ-5000CR-ESD, BLQ-5000CR-ESD-15, BLQ-7000CR-ESD
Accessories
  • Pistol Attachment PAB-70
    This attachment converts a screwdriver to a pistol-style screwdriver, most suitable for horizontal screw fastening.

Brushed electric screwdrivers

CL-light series (DC Type)

Light torque, small screw applications!
  • This screwdriver is specially designed to deliver accurate, low torque for fastening small sized screws.
  • Compact and light-weight design makes it easy for female operators to use.
  • Model CL-2000 has a coreless motor with an espescially long life.
  • With safety design running on low voltage and direct current, these screwdrivers can be used safely.
Lever Start type

CL-2000: Output Torque range N.m 0.2-0.2
CL-3000: Output Torque range N.m 0.03-2
CL-4000: Output Torque range N.m 0.1-0.55

Push-to-start type

CL-4000PS: Output Torque range N.m 0.1-0.55

CL-standard series (DC Type)

Standard to medium torque applications!
  • This screwdriver has been a long-selling product thanks to its operability, reliability and stability.
  • With low DC voltage these screwdriver scan be used safely.
  • The grip design helps operators to reduce fatique caused by long hours operations.
Lever Start type

CL-6000: Output Torque range N.m 0.2-1
CL-6500: Output Torque range N.m 0.3-1.6
CL-7000: Output Torque range N.m 0.3-2.5

Push-to-Start type

CL-6000PS: Output Torque range N.m 0.2-1
CL-6500PS: Output Torque range N.m 0.3-1.6
CL-7000PS: Output Torque range N.m 0.3-2.5

CL-hight toque series (DC Type)

High torque applications up to 5 N.m!
  • This driver can tighten high-torque required screws which are tightend by pneumatic screwdrivers.
  • Can always fasten scews with stable torque.
  • The Shockless Stand absorbs reaction force created by the clutch.
Push-to-Start type

CL-9000 (with shockless stand): Output torque range N.m 1.5-5

Hios AC screwdrivers (transformerless systems)

Brushless electric screwdrivers

VB series (AC Type)

Transformerless!
  • Energy saving and cost reduction can be achieved by reducing power consumption by about 50% (compared with conventional HIOS product).
  • The temperature rise of the motor is reduced by about 30% and reduces errors  caused by heating.
  • Can be directly plugged into AC outlet.
Lever Start Type

VB-1510: Output Torque range N.m 0.25-1.5
VB-1510-18: Hi-speed rotation Output Torque range N.m 0.25-1.5
VB-1820: Output Torque range 0.4-1.8
VB-3012: Output Torque range 0.5-3
VB-4504: Output Torque range N.m 1-4.5

Push-to-Start Type

VB-1510PS: Output Torque range N.m 0.25-1.5
VB-1820PS: Output Torque range N.m 0.4-1.8
VB-3012PS: Output Torque range N.m 0.5-3
VB-4504PS (with shockless stand): Output Torque range

 

Accessories
  • Suction (Vacuum) Attachment for VB Series,  VB-1820/ VB-3012
    By negative pressure the effort needed to pick up screws is reduced. This attachement
    can even pick up non-ferrous screws such as stainless steel screws by vacuuming and
    improve operation efficiency. It also removes powder dust generated in screw fastening.
  • Pistol Attachment PAB-18 for Lever Start & PAB-18PS for Push-to-Start
    This attachment converts a scewdriver to a pistol-style, most suitable for horizontal
    screw fastening.
  • Angle attachment ANGLV-Z-CH1 & ANGLV-XX1
    This attachment is most suitable when the available space is very small fors crew fastening. The attachment can be fitted to the tip of the screwdriver.
VBH series (AC Type)

Transformerless Ultrahigh Torque Brushless® Screwdrivers!
  • Hammer-head screwdriver ideal for assembling products requiring high torque.
  • These screwdrivers can apply high torque like pneumatic screwdrivers
  • Can always tighten screws with stable torque
  • The Shockless Stand absorbs reaction force created by the clutch
Lever Start Type

VBH-1820 (with shockless stand): Output Torque range N.m 3-7
VBH-3012 (with shockless stand): Output Torque range N.m 4-10

Push-to-Start Type

VBH-1820PS (with shockless stand): Output Torque range N.m 3-7
VBH-3012PS (with shockless stand): Output Torque range N.m 4-10

Brushed electric screwdrivers

VZ series (AC Type)

Transformerless!
  • Transformerless screwdrivers suitable for heavy-duty Production.
  • Can be directly plugged into an AC outlet.
  • Light and slim balanced body design that minimizes operator fatique.
Lever start type

VZ-1812: Output Torque range N.m 0.4-1.8
VZ-3007: Output Torque range N.m 0.9-3
VZ-4504: Output Torque range N.m 1-4.5

Push-to start type

VZ-1812PS: Output Torque range N.m 0.4-1.8
VZ-3007PS: Output Torque range N.m 0.9-3
VZ-4504PS: Output torque range N.m 1-4.5

Accessories

Suction (Vacuum) Attachment VZQ
By negative pressure the effort needed to pick up screws is reduced. This attachement can even pick up non-ferrous screws such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fastening.

Pistol Attachment PAB-18 for Lever Start & PAB-18PS for Push-to-Start
This attachment converts a scewdriver to a pistol-style, most suitable for horizontal screw fastening.

Angle attachment ANGLV-Z-CH1 & ANGLV-XX1
This attachment is most suitable when the available space is very small fors crew fastening. The attachment can be fitted to the tip of the screwdriver.

PS Front Cover ring VZ18-0960
This helps you to easily apply load in the axial direction to reduce workload.

Protective Cover for Torque Adjustment Nut VZ18-0970
This cover prevents change in torque by operation during operation

Shockless Stand VZ18PS-SAS
The Shockless Stand absorbs reaction force created by the clutch. The Stand can be used only with Push-to-Start screwdrivers.

Hios screwdrivers for automated machines

Brushless electric screwdrivers

PGF series (DC Type)

Utilize the data of screw fastening operations!
  • The built-in torque sensor judges (OK/NG) for every screw fastening
  • The problems that are difficult to see such as insufficient torque, cross threaded and floating screw can be detected
  • Screw fastening operation data can be output to a PLC or computer
  • An external device can be used to control the direction and speed of driver rotation

PGF-3000: Output Torque range N.m 0.2-0.55
PGF-5000: Output Torque range N.m 0.4-1.2
PGF-7000: Output Torque range N.m 1.0-2.8

PGF Applicable Drivers
Suction (Vacuum) Attachment

PGFQ
By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screw such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fasterning.
Models: PGFQ-3000, PGFQ-5000 and PGFQ-7000.

PGFR
The PGFR Attachment is ideal for deeply recessed screws. Torque adjustment is possible without removing the attachment or removing the driver from the machine. The attachment uses bits which means replacement bits is less costly than long bits.
Model: PGFR-7000

Power supply for Brushless drivers for automated machines

Models: BLT-AY-61 and BLT-AY-71

  • 2WS (2 Speed) and REV (Reversing) capabilities formerly optional are in these power supply as standard
  • Can be connected to external devices such as a PLC to control the direction and speed of driver rotation
Driver Cord

BLF7-0612-VI

BLF Damper Unit

This unit absorbs the impact against the workpeice while the Z-axis is descending and reduces the load on Model: BLF-DP

BLF series (DC Type)

Brushless® Screwdrivers for automated assembly machines!
  • Simply structure provides high durability and easy maintenance

BLF-2000: Controlled Torque range N.m 0.03-0.35
BLF-5000: Controlled Torque range N.m 0.3-1

Suction (Vacuum) Attachment

BLFQ
By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screw such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fasterning.
Models: BLFQ-2000, BLFQ-5000 and BLFQ-7000

BLFR
The BLFR Attachment is ideal for deeply recessed screws. Torque adjustment is possible without removing the attachment or removing the driver from the machine. The attachment uses bits which means replacement bits is less costly than long bits.

Power supply for Brushless drivers for automated machines
  • 2WS (2 Speed) and REV (Reversing) capabilities formerly optional are in these power supply as standard
  • Can be connected to external devices such as a PLC to control the direction and speed of driver rotation
Driver Cord

BLF7-0612-VI

Brushed electric screwdrivers

CLF, αF, CL-A Series (DC Type)

Brushed Screwdrivers for automated assembly machines!
  • Suitable for automated assembly machines
  • Stable torque accuracy helps to uniform fastening to automation
  • Easy to install to the existing assembly system thanks to the compact body
  • Many variations
Low Torque CLF Series

CLF-4000: Controlled Torque range N.m 0.1-0.35
CLF-6000: Controlled Torque range N.m 0.3-0.6
CLF-6500: Controlled Torque range N.m 0.4-1
CLF-7000: Controlled Torque range N.m 0.5-1.5

High-speed αF Series

αF-4500: Controlled Torque range N.m 0.4-0.6
αF-5000: Controlled Torque range N.m 0.4-0.75
αF-6500: Controlled Torque rabge N.m 0.5-1.1
High torque CL-A Series
CL-816A: Controlled Torque range N.m 1.5-2.5
CL-825A: Controlled Torque range N.m 2-4
CL-850A: Controlled Torque range N.m 2.4-4.5

Suction (Vacuum) Attachment

CLFQ/ αFQ
By negative pressure, the effort needed to pick up screws is reduced. This attachment can even pick up non-ferrous screw such as stainless steel screws by vacuuming and improve operation efficiency. It also removes powder dust generated in screw fasterning.
Models: CLFQ4-SET and CLFQ65-SET

Power Supply for Brushed Scewdrivers for Automatic Assembly Machines

Model: BLT-AY-61

Hios reciprocating screwdrivers

Brushless electric screwdrivers

RN53 Recipro Series (DC type, AC type)

Reciprocating Brushed screwdriver!
  • Unique automatic feeding system allows wider variations in screw tightening
  • Ideal for deeply redessed screws
  • Easy maintenance because the screwdriver, screwfeeder, power supply and hose assy can be seperated

Model: RN53-200, Recipro screwdriver RD-4000: DC type Output Torque range N.m 0.1-0.55
Model: RN53-260, Recipro screwdriver RD-4500: DC type Output Torque range N.m 0.3-0.8
Model: RN53-300, Recipro screwdriver RD-10: AC type Output Torque range N.m 0.2-1
Model: RN53-300, Recipro screwdriver RD-15: AC type Output Torque range N.m 0.2-1.5
Model: RN53-400, Recipro screwdriver RD-20: AC type Output Torque range N.m 1-2
Model: RN53-400, Recipro screwdriver RD-30: AC type Output Torque range N.m 1-3

Screw Feeder FF503H
  • Feeding speed is adjustable according to screw type and size
  • The air feed system automatically and instantly feeds a screw to the bit
  • The vibrational frequency and amplitude of the feeder is adjustable
Power Supply RDT-30 DC type

For screwdriver RD-4000 and RD-4500

Power Supply RAC-100 AC type

For screwdriver RD-10, RD-15, RD-20 and RD-30

Hios power supply

Power Supply for HIOS DC screwdrivers

Exclusive power supply is required for HIOS DC screwdrivers!
  • Exclusive power supply converts the electric current from AC outlet to low-voltage output (HI:DC30V) or (LOW:about DC20V) to supply it to the screwdriver.
  • Safe and quiet rotation.
  • Please use HIOS screwdriver in combination with HIOS power supply for safe screw tightening.
  • Stable power supply with multiple inputs (AC100V to 240V)
Power supply for HIOS Brushless srewdrivers

T-45BL & T-70BL

Power supply for HIOS Brushed screwdrivers

CLT45, CLT60, CLT80, CLT100

MC-70L is for multiple screwdrivers. When you use MC-70L, you need to connect a control box CB-105.

Hios peripherals and accessories

Screwdriver Cord

    1.5M (5P)

    Compatible models:
    BLG-4000, BLG-5000, BL-3000, BL-5000 Series, CL-2000, CL-3000, CL-4000, SS-2000, SS-3000, SS-4000, α-4500, α-5000

    2M (5P)

    Compatible models:
    BL-7000 series, CL-6000, CL-6500, CL-7000, SS-6500, SS-7000, α-6500

    2M (6P)

    Compatible models:
    PG, BLG-BC2, BLG-BC1, BLG-ZERO1, BLG-OPC, BL-OPC Series

    3M (5P)

    Compatible models:
    CLF-6000, CLF-6500, CLF-7000, αF-6500

    Flexible Scewdriver Cord

    Flexible cord that endures kinking and bending

     

    2M (5P)

    Compatible models:
    BLG, BL, CL, SS, α Series

    3M (6P)

    Compatible models:
    BLG-BC2, BLG-BC1, BLG-ZERO1, BL-OPC Series

    Curled Cord

    Elastic and flexible cord

    7.5M (5P)

    Compatible models:
    BL, CL, SS, α Series

    Extension Cord

    Use this cord as an extension cord when the standard cord is not long enough

    3M (5P)

    Compatible models:
    BLG, BL, CL, SS, α Series

    5M (5P)

    Compatible models:
    BLG, BL, SS, α Series

    Grip Ring TM.D.PAT

    Screwdriver can be surely gripped and doesn’t slip
    • Reduce operation fatique by preventing grip slip
    • Multiple color rings help identipication of driver
    • Protects the screwdriver from shock and scratches
    • Can be removed cleanly without damage
    Single color 10 pc in 1 pack

    Red (GRIP-R10), Green (GRIP-G10), Blue (GRIP-BL10), Yellow (GRIP-Y10) White (GRIP-W10)

    Compatibles models: All models (except BL-2000/CL-2000/SS-2000)

    Controller - SB Series

    Reverse operation is performed when tapping is complete or when overloading is detected thereby preventing tap breakage.

    Model: SBC-1

    Comptible tappers: SB-400, SB-650C

    Vacuum Pump VP-3

    For suction type screwdrivers

    A vacuum is generated to pick up and hold the screw on the bit tip.

    Stripped Screw Remover

    HIOS Spike®Bit D.PAT (for precision screws)

    SPK Series

    This is a specially designed tool to easily remove screws with damaged recesses. Ideal for unscrewing high-end products such as HDD.

    Grip color Yellow, applicable screw size: M1.2-M1.4
    Grip color Blue, applicable screw size: M1.4-M1.7
    Grip color Red, applicable screw size: M1.7-M2.0

    Vertical Srewdriver Operating Stand

    The stand keeps the screwdriver in a vertical position, allowing accurate screw tightening.

    VMS-40: for BLG-BC2/BLG-BC1/BLG/BL/SS/α/VZ-1510
    VMS-50: for PG/BLG-BC2/BLG-BC1/BLG/BL/CL/SS/α/VZ-1510
    VMS-50VZ: for PG/VB/VZ (except VZ-1510)

    Screw Counter SCT3 series
    The number of fastener count can be set from 1 to 99
    • A buzzer will sound when the final screw has been fastened to notify you of screw fastening completion
    • The fastener count number is automatically reset after all screws have been fastened. The screwdriver will be disable until the next “work set confirmation” SET signal is input (not applicable to SC3 series)
    • Prevents counting double-fastening
    • Can be used as a normal power supply by disabling the count function (applicable only to BLOP-STC3 and CLT-70STC3)

    Model BLOP-SC1 (for one screwdriver), compatible for:
    BL Series, BLG Series, BLG-ZERO1 Series, BLG-BC1 Series,BLG-BC2 Series

    Model CLOP-SC1 (for one screwdriver) compatible for:
    CL Series, SS Series, α Sries

    Automatic Screw Feeder - HS series
      
    For manual & automatic assembly machines
    Neji Taro aligns srews

    The work efficiency of a production line will be dramatically improved.

    • A single unit can handle different screw sizes by changing rails.
    • Easy rail replacement
    • Screws are stably aligned and quickly fed to a line
    • Feeding speed can be adjusted depending on operational conditions
    • Some models can handle special screws

    Model selection chart: Neji Tavo V, Neji Taro II, Neji Taro III, HSF

    For manaul operation HSV series, for automatic assembly machines HS-RB series

    Screw size varies from M1.0 – M5.0

    Hios torque meters

    Torque Meter HP/ HDP/ HM/ HIT Series

    HIOS Torque Meters are the industry benchmark
    • Measured data can be imported to a computer
    • Up to 100 data can be stored in the memory and controlled (applicable to HP & HDP only)
    • With one unit of Torque Meter, max, mi and ave torque values can be measured (applicable to HP and HDP only)
    • New product, HP-1 is ideal for measuring 10N.cm or smaller torque
    • Torque for both clockwise or counterclockwise  can be measured
    • As a standard specification, data output and analogue output are available
    • We offer calibration and maintenance services
    • “Inspection Report” is attached to all Torque Meters

    HP-1, HP-10 (N.m 0.015-1.000) and HP-100 (N.m 0.15-10.00)
    Use for making torque settings  on electric screwdrivers, checking torque of torque wrenches or measuring orque of various rotating units etc.

    HDP-5 (N.m 0.015-0.500), HDP-50 (N.m 0.15-5.00), HDP-100 (0.15-10.00)
    Use for measuring loosened torque of tighened screws or additional tightening torque

    HM-10 (N.m 0.015-1.000), HM-100 (N.m 0.15-10.00)
    Use for torque control of screwdrivers for automatic assembly machines

    HIT-200 (N.m 0.15-18.00). HIT-500 (N.m 1.5-50.0), HIT-2000 (N.m 25.0-180.0)
    Use for control of impact drivers and torque wrenches

    Hios electric tappers

    Brushless electric tappers

    Electric Tapper BL (DC Type) Brushless
    With an automatic reversal mechanism, this tool detects overloading and prevents tap breakage
    • Tapping tools for components with pilot holes
    • Automatically detects excessive load on the tap and the pilot hole and returns the tap to prevent hole damage. For through or blind holes, operational efficiency increases because the tap automatically stops and returns when the specified depth is achieved
    • With this tool tap cleaning can be done easily to prevent screw tightening errors caused by paint or adhesive remaining in the hole
    Lever Start Type

    BL-5000SB: Tapping capacity 0.9-2.6

    Two-way Start system

    BL-7000SB: Tapping capacity 2.0-4.20

    Power Supply

    For BL-SB series: T-70BL

    Brushed electric tappers

    Electric Tapper (DC Type) Brushed

    Lever Start type

    SB-400C: Tapping capacity 0.9-2.6
    SB-650C: Tapping capacity 2.0-4.0

    Power supply

    For SB series: T-45BL

    Do you like what you see?

    Maybe our creative solutions can be part of your production process.

    For more information call:
    Gert-Jan Hollestelle
    +31 (0)226-335010 (Dutch, German, English)

    7 + 3 =